Shoes for Sybarite

I found some tiny stickers and wanted to use them for doll shoes. As I hadn't made anything for the Sybarite in a long time, I decided to use the resin soles I made some time ago.

First step was painting them. I used two tiny plastic cups and attached the soles to them with double-sided mounting tape to be able to paint all sides at once (except the insoles). I used Revell Enamel Paint number 04 for these.

Here is the sheet of stickers. You can't really see the scale, but the photos further below will make that clear.

For the uppers, I decided to use clear plastic. Below you can see the type of plastic I'm using for the doll shoes. It is soft and doesn't show any creases even after doing this:

The insoles have two layers of cardboard and one layer of leather, and I painted the edges.

The following photos show the order of attaching the stickers.

I even decided to put some on the insoles where they would remain visible.

After attaching all stickers, it was time to apply sealer. Again I attached the soles to the plastic cups to get even layer of sealer on all sides.

The uppers are very simple as there is no point doing anything very elaborate when using clear plastic alone (without any stickers).

I cut the pieces from the plastic and used the lines in the pattern to attach pieces of double-sided adhesive tape to the parts that go under the insole.

After making holes to the flaps, I attached the uppers. For more information on why I made the holes, see an earlier blog post.

Then I just needed to glue the insoles in place. Here are the finished shoes from several angles.

More experiments with polymer clay

I was wondering if I could make something like the modified plastic castings in the previous post, but use polymer clay. I made a similar mold (only taller) using cardboard and cut pieces from the sides, so I could cut the clay after filling the mold.

Then I covered those openings with pieces of cardboard attached with adhesive tape. This helps in filling the mold.

When the mold was full, I removed those extra pieces.

Then I cut along the edges of the openings. That wasn't easy as the clay was a bit too soft even after a few hours in a fridge. Soft clay is easier when filling the mold, but makes cutting more difficult. The surfaces required some work after cutting to make them even.

Here are the soles after baking and removing the molds. I'm not quite happy with the shape, so I think these will have to be cut and sanded quite a bit. Still, I've got two soles of similar shape and size to work with, which is more than I could do without using molds.

Plastic castings

I decided to make soles for Monster High shoes using the plastic that is melted by heating (more details here). First I made simple wedge soles. I started by cutting the parts of the molds from thin copper sheet lined with packing tape.

Then I used pieces of the same tape to assemble the molds.

Here are the molds filled with hot plastic and waiting to cool down. The molds are attached to a piece of wood with double-sided tape to make sure they stay in correct position.

And here are the finished soles. This pale yellow is the original color of the E-Z Water plastic pellets.

Then I decided to experiment a bit and made molds for soles with separate heels for Nefera. I just modified the pattern I used for the polymer clay soles.

I was actually quite surprised to see that this worked. If it hadn't, I would have just returned the pieces to the melting pot for re-use. These soles are slightly darker than the previous ones, because I was running out of plastic and had to add a previously slightly overheated batch into the pot. Overheating makes the plastic get darker (and serious overheating makes it smoke and smell bad). The correct temperature to use is the lowest in which you can get the plastic to melt. My stove has a scale of 0 to 12 and setting 5 is just right for this.

Shoes for 16" Miss Piggy

The basis for these shoes were plaster castings I had made some time ago. I glued the platform toe parts to cardboard soles that had 3 layers of cardboard glued in shape.

Next, I covered the sides of the toe parts with leather and filled gaps with leftover pieces to make sure that the outer soles would stay even when glued in place.

Then I covered the plaster casting heels with leather and glued them in place. Usually the heels are the last part to be glued, but I wanted to try a different method this time.

Then I covered with leather the edges that still had cardboard visible. The metal strip you can see in the photo is there to provide extra support to keep the arch in correct form. I don't use that a lot, but Piggy weighs more than smaller dolls, so some additional strength is a good idea.

For the closing mechanism I decided to try hook and eye, which turned out to be a bad idea as you can see later.

The straps are made of leather and the decorations are actually sticker strips with transparent background. Those are really easy to use for something like this. I covered the strips with glossy sealer just to be sure that nothing will fall off later.

The insoles are made of cardboard and covered with leather leaving some extra around the edges. I cut off the extra where the straps went, but in other places I turned it under the soles.

Here you can see the insoles with some sections already turned under.

The problem with hook and eye was that the end of the strap pointed to the side instead of going along the side of the foot. As I had already glued the pieces in place, I decided to fix this by cutting the hooks, pressing them flat and gluing the straps to the leather strips that held the hooks. So the result is no closing mechanism at all, but fortunately Miss Piggy's feet are different from most other dolls' feet and even shoes with fixed straps placed this high will be fine.

Finally, here are the finished shoes. The outer soles are finished with pieces of dark brown leather.

Platform sandals for Miss Piggy

As I was looking through some fashion magazines from this year and cutting shoe pictures for later reference, I got several new ideas. One of them came from this picture of a Prada shoe. I rarely make replicas, so the basic construction is from this, but I used black leather and the fabric I used for Monster High doll shoes earlier.

I started by cutting the toe parts from cork. I used leftover pieces from the cork board I used for the dollhouse front wall, so it was too coarse to be used as such, but was fine for this as it was going to be covered in thick leather. The heels are cut from a round wooden stick. Getting the right angle on the top was tricky as a mitre box is meant for cutting in 45 degree angle, which would have been too steep. So, I had to keep the piece of wood in angle in the mitre box during sawing.

I covered the pieces with leather. The pieces of leather in the top and bottom of the cork parts are there to help keep the soles even.

The insoles have two layers of cardboard and one of leather. The outer soles have three layers of cardboard with leather strips glued to the sides and leftover pieces glued to the top and bottom. The cardboard in the insoles will take care of small unevenness, but without the leftover pieces in the middle of the outer soles, the center part of the insoles would be lower than the edges when the soles are glued together.

The straps are glued in place here. They consist of leather strips covered with fabric (the fabric was too thin to use alone). The leather parts do not go under the insoles, just the fabric. Leather is too thick and would make the insoles bumpy.

Here are the parts so far. The parts that go behind the heel are made of leather and one layer of cardboard. The reason for using cardboard is that it keeps the parts in correct shape when you glue the fabric in place.

Next, I glued the cork parts to the outer soles and covered the heel parts with fabric. The light colored leather pieces shown beside them are the innermost pieces that will cover the flaps of glued fabric.

This closeup shows the construction better. The ankle straps are also in place here and so are the beads that will be used for closing them. The ends of the straps and the thread used to attach the beads will all be hidden under the leather pieces.

Here is the upper part of the right shoe almost finished.

The same in a side view after gluing the outer sole in place.

The loops for closing the ankle straps are made of thin rubber band and glued in place.

Almost finished. The parts in the middle are the leather pieces to be glued on the bottom of the outer soles to cover them.

The final step was to glue the heels in place. Here are the finished shoes.

And finally, the shoes on Miss Piggy's feet.